SKU : JPE1000HDF-SIDEMUFFLER
Side mount muffler for the Jono & Johno 33HP JPE1000HDF V-twin engine — mounts on the side, not the rear.
The standard muffler on this engine sits above the PTO shaft at the rear. If that space is taken — by a pump, a gearbox, a clutch housing or a guard — there is nowhere for it to go. This muffler does the same job from the side of the engine instead, and gives the rear of the engine back to you.
It is a straight swap for the standard muffler, not an addition to it. The mounting bracket is welded to the body, so there is nothing to fabricate and nothing to line up by eye.
| Spec | Detail |
|---|---|
| Type | Side mounting muffler with perforated heat shield |
| Mounting | Bracket welded to the muffler body |
| Inlet | Twin flanges, 60mm bolt hole centres |
| Outlet diameter | 40mm |
| Body diameter | 130mm |
| Heat shield length | 420mm |
| Finish | Black |
| Part number | JPE1000HDF-SIDEMUFFLER |
Jono & Johno JPE1000HDF 33HP 1000cc V-twin horizontal shaft engine.
This muffler suits that engine only. The body size and the welded bracket are specific to it — it will not fit the 22HP JPE750HDF or any of the single cylinder engines in the range.
Exhaust gaskets are not supplied. Fit new ones rather than reusing the old gaskets off the engine — they crush flat on first use and will not seal a second time. Lower muffler mounting bracket shares the engine mount bolts, so existing engine bolts must be used for that.
This muffler replaces the standard rear mounting muffler supplied with the engine. You use one or the other, not both. For the complete engine, see our 33HP 1000cc V-twin horizontal shaft engine with electric start.
Standard trade practice, not specific to this part: start both flanges on their studs and run every nut up finger tight before you torque any of them. Tightening one flange down first pulls the muffler out of line and loads the other flange on an angle, which is how exhaust flanges crack. Once the engine has been up to temperature and cooled again, go back and re-check the nuts — the gaskets settle on the first heat cycle and they will have loosened off.
Dimensions:
*Exhaust manifold hangs over shaft, leaving 80mm of shaft projecting. (Shaft protrudes from bolt face by 110mm.)
*Centre line of engine to muffler exit extremity 415mm
*Muffler diameter 130mm
*Muffler height (including heat shield) 425mm
*Left hand engine mount to the muffler exit extremity 200mm
*Ground clearance 5mm (5mm above engine mount deck)
*Total width of engine, one side to the other muffler exit extremity 650mm
*Total depth of engine and muffler 450mm
*Exhaust manifold protruding from exhaust openings 135mm
Jono & Johno offers a 12-month warranty on most products.
We pride ourselves on selling good quality gear and will be fair and prompt in honouring our warranties. If you’re in trouble, we’ll help you out.
The exact warranty coverage depends on two factors:
Minor faults caused by the user
Minor faults caused by the manufacturer
Major faults caused by the manufacturer
Major faults caused by the user
If you need to return your product:
Some products are not covered by warranty, including:
If your product is out of warranty and has failed despite minimal use, contact us. We may assess it on a case-by-case basis. If a manufacturer defect is identified, we aim to be fair in resolving the issue—but this is at our discretion.
| SKU | JPE1000HDF-SIDEMUFFLER | |
| Model # | JPE1000HDF-SIDEMUFFLER | |
| Barcode # | 721814475999 | |
| Brand | JONO & JOHNO | |
| Shipping Weight | 5.7300kg | |
| Shipping Width | 0.500m | |
| Shipping Height | 0.250m | |
| Shipping Length | 0.360m | |
| Shipping Cubic | 0.045000000m3 | |